Panasonic ip camera utility1/3/2023 ![]() ![]() If the camera requires a username and password, then put the credentials in the Remote Host Name field on the Monitor -> Source tab for the camera in ZoneMinder like this: An easy way to reduce CPU load is to set the "Maximum FPS" field on the monitor General tab to 15 or less, but ZoneMinder performs better if frame rate limiting happens at the camera. If the CPU becomes overloaded, then the zmc process will crash and the Feed Watch page will be blank or show the broken image icon. Doing this on one stream can consume an entire core on a modern CPU. ![]() ZoneMinder transcodes the MPEG4 stream to add a banner or stream through the web interface. Remember to reboot the camera on the "Maintenance" tab after changing these options. To reduce streaming bandwidth, reduce both the frame rate and the maximum bit rate on the "Setup -> Video Streaming" page. If the frame rate is decreased at the default maximum bit rate, then streaming image quality will noticeably improve. The raw idle RTP output of a bright quiet scene for these cameras is usually 400 kbps, or 5GB per day.Įven if the RTSP stream is frame limited by the camera, the transport will be at 30fps. In RTSP mode, ZoneMinder can get 30 fps from a Panasonic netcam that has an MPEG4 encoder. Note: Audio can be enabled on models that have it by changing the nil to g726, but ZoneMinder lacks audio support, so doing this would waste network capacity and storage. Note: The camera must be manually rebooted for MPEG-4 or H.264 options to take affect. Video streaming options are always global and can only be changed through the CGI or web interface. Note: Only high definition models support the 1280x1024 resolution. Note: Low end models like the Panasonic BL-C1A Petcam only support MJPEG because they do not have an MPEG4 encoder. On the Monitor -> General configuration page for the camera in ZoneMinder, leave the Maximum FPS field empty. Remote Host Path: nphMotionJpeg?Resolution=640x480&Quality=Standard&Framerate=10 For example, to limit capture to 10 fps, set: On slow or busy systems, ZoneMinder performs better if the frame rate is externally limited at the camera. In ideal conditions with tuning, the maximum is approximately 25 fps. In MJPEG mode with a default configuration, ZoneMinder can sustain approximately 5 fps from a Panasonic netcam. Frame Rate" option, which is set on the Video Streaming page. Note: The default MJPEG frame rate in the web interface is the same as "MPEG-4 Max. Remote Host Path: nphMotionJpeg?Resolution=640x480&Quality=Standard&Framerate=0.5 For example, to take an image every other second: The optional Framerate parameter can be 0.1 through 30.00 frames per second in one-tenth increments. Note: Only hi-def models support the 1280x1024 resolution, and some low end models like the Panasonic BL-C1A Petcam do not support the 640x480 resolution. ![]() The required Resolution CGI parameter can be one of 1280x1024, 640x480, 320x240, or 160x120 pixels. ![]() The required Quality CGI parameter sets JPEG quality and can be one of Clarity, Standard, or Motion. Remote Host Path: cgi-bin/nphContinuousServerPush?Resolution=640x480&Quality=StandardĬameras models that only have the old version 2.00 firmware interface are: Remote Host Path: nphMotionJpeg?Resolution=640x480&Quality=StandardĬhange nphMotionJpeg to nphContinuousServerPush or cgi-bin/nphContinuousServerPush if the camera has old firmware like this: Only set access credentials on Panasonic equipment after you have a working ZoneMinder configuration.Īt the Monitor -> Source page for the camera: Change Video Display Time to Unlimited.Set privileges on the guest account for ZoneMinder:.ZoneMinder 1.25 expects version 3.00 or later. If you are not using the configuration utility for Microsoft Windows, then you may need to do something like `sudo ifconfig eth0:0 192.168.0.2` at a terminal prompt to access the camera and enable DHCP. Many firmware revisions ship with DHCP disabled by default. The camera uses a default IP address of 192.168.0.254 if it does not get a DHCP lease. ![]()
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |